Setting up A Bathtub
Setting up A Bathtub
Blog Article
The article down below relating to Tools You Need to Install a New Bathtub is without a doubt attention-grabbing. Don't miss it.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently accessible, the project can move easily; if you have to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bathtub in your bathroom if you have already purchased a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product list need to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth all set for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the supply of water and also examine all joints and new pipework for leaks as well as tighten them if required. Fill up the tub as well as additionally check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub must wait up until the bathtub has actually been made use of at the very least when as this will resolve it right into its final position.
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, bring about complications with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealant can fracture relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the market. It is suggested to fit the ceramic tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very involved in How to Install a Bathtub Yourself and I really hope you appreciated my entry. In case you appreciated our blog post kindly make sure you remember to share it. We thank you for reading our article about Installing A Bathtub.
See Availability
Report this page